The blue crab or the Atlantic crab is one of the most common sources of fresh crab meat in Europe and North America. Catching crabs is a beneficial hobby and can be made even more productive by building and setting traps. You can easily make your own blue crab traps with a few specialized materials. Make sure you get the exact materials listed or the proportions of the instructions will be inaccurate. You can find these things at fishing or building supply shops.

Step 1

Cut two lengths of crab pot wire that are 20 mesh long and one length that is 11 mesh long with wire cutters. Mesh is the number of loops in row, so 20 mesh is 20 loops long.

Step 2

Bend the ends of a 20 mesh sheet of wire up so they are at a 90-degree angle with the middle of the wire. The bends should be made 6 mesh in from either end and form a square “U” shape; this should be done to both 20 mesh sheets.

Step 3

Fold the 11 mesh wire in half into a “V” shape. You need to make a 1 mesh spine on the fold, so that there is 1 mesh down the middle and 5 mesh down both folded sides.

Step 4

Snip open two openings on the spine of the “V” shape. The openings should both start 1 mesh from the finished edges and should have 8 mesh between them.

Step 5

Cut four small pieces of wire that are 2 mesh long and cut each into a trapezoid. The upper row should be 10 mesh wide and the lower row should be 12 mesh wide.

Step 6

Wrap the trapezoid pieces so each piece’s edge meet and form four separate cone shapes. Twist the end wire together to make the shape stay put. These are the four funnel entrances.

Step 7

Cut a piece of eelpot wire into a 12 by 12 mesh rectangle and roll it into a tube shape.

Step 8

Secure the tube at the edges with crab pot staple. You can tighten the staples using pliers until they hold the wire tightly.

Step 9

Compress one open end of the tube until it is flat. Fix this end closed with the crab pot staples, leaving only one end open. This is the bait box.

Step 10

Place the “V” piece inside the “U” shape. The spine of the “V” should be facing up and the edges should be positioned 2 mesh up from the bottom of the vertical “U” walls.

Step 11

Twist the end wires of the “V” and the “U” shapes together to attach them. The trap should look like a little house with extended vertical sides.

Step 12

Remove a full mesh from the very middle of the floor of the trap with the wire cutters.

Step 13

Fit the open end of the bait box into the hole in the bottom of the trap and secure them together with crab pot staples. The bait box should be inside the trap, under the “V” roof.

Step 14

Cut an opening on the lower edge of each side of the trap. The opening should be able to accommodate the larger opening of the funnel entrances.

Step 15

Turn the other bent 20 mesh sheet so it is an upside down “U” and place it on the trap to form a closed box shape.

Step 16

Twist all of the wires together along the edges except for one edge along the top of the box. This is the opening of the box to get the crabs out.

Step 17

Attach a length of 11-gauge smooth wire to both edges along the open side of the trap. Use the crab pot staples to attach the wire and make the edges smooth.

Step 18

Snip one mesh of wire in any two upper corners of the trap. Don’t cut the wire away; just snip them open.

Step 19

Bend the snipped wires back and place a cull ring around the bent wires. Fold the wires so the rings are held tight against the trap. These rings will let smaller fish out of the trap.

Step 20

Tie a length of bungee cord to the inner side of the trap opening. Use crab pot staples to attach the cord to the edge on the horizontal side of the trap, not the vertical one.

Step 21

Tie the loose end of the cord to a clip and use the clip to hold the trap closed.

Please contact with us if any questions , our sales team will always be happy to provide you with the most professional info.